Bathrooms and kitchens are where an apartment makes most of its moisture, and they are also the rooms most likely to be boxed in with limited windows. Add a shared wall or two and a duct that runs through common property, and a patch of mould above the shower stops being a simple cleaning job. This guide covers why it happens, what you can do inside your own unit, and where the building and its rules come in.
Consumer NZ's guidance on mould describes it as a fungus that grows in damp places, appearing as coloured growth or staining on walls, ceilings and other surfaces. It needs moisture, and the usual trigger is warm, moist air from showers and cooking meeting a cold surface. Its published figures for how much water a household puts into the air are a useful reality check: about 1.5 litres per person per day from showers and baths, about 3 litres a day from cooking, and about 5 litres for each load of washing dried indoors.
In an apartment, a small bathroom might be taking most of that moisture with only a fan between the steam and the rest of the unit. Mould usually shows first on bathroom ceilings, around window frames, in silicone and grout, and behind or inside cupboards where air does not circulate.
Cleaning without fixing airflow only buys a few weeks. Consumer NZ suggests running the extractor fan during cooking or showering and leaving it on for roughly ten minutes afterwards, opening windows for ten to fifteen minutes each morning, keeping lids on pots and wiping condensation off glass and walls. A professionally installed shower dome is another option it mentions, and so is a dehumidifier or the dry mode on a heat pump.
If you rent, the healthy homes ventilation standard sets the baseline. Per the Tenancy Services ventilation standard, kitchens and bathrooms need an extractor fan that vents outside. For fans installed after 1 July 2019 the minimum is a 150 mm diameter (including ducting) or 50 litres per second capacity in kitchens, and 120 mm or 25 litres per second in bathrooms. Older fans that were installed before that date still count if they vent outside and work. Recirculating systems and fans that do not vent outdoors do not meet the standard.
This is the part that is different from a house. A fan that vents through an exterior wall or into a shared riser may involve common property, and the government's unit titles guidance says that if work will affect another unit or the common property, you must tell the body corporate and obtain written consent from it and any affected owners. Check your operational rules before commissioning a new fan, a duct or a penetration in an exterior wall.
Landlords in unit title buildings have some relief here. The unit titles healthy homes guidance explains that a landlord who does not own the whole building may be partially exempt where they cannot install or reach something in a part of the building they do not solely own. They must still take all reasonable steps to comply as far as practicable, which in practice means asking the body corporate for consent rather than assuming it will say no.
If mould keeps returning despite good ventilation, there may be a hidden source. Tenancy Services says a qualified building surveyor may need to check the property, because hidden moisture left for long enough can cause expensive damage. In a shared building, a recurring patch on an external wall or a shared ceiling is worth reporting to the committee or manager, since a leaking pipe, a failed seal or a defect in the building envelope would be a body corporate matter rather than a personal one.
The two guides offer slightly different ratios, so follow the one that suits the surface and always test a small patch first.
Both stress protection. Open a window, wear gloves and eye protection, and use a well-fitted mask; Consumer NZ recommends a P2 or N95 type. Avoid dry brushing, which sends spores into the air, and bin the cloths afterwards. People with asthma, respiratory problems or weakened immune systems are at greater risk from mould spores.
Consumer NZ also notes that mould in silicone and grout is difficult to remove because it grows roots into the material. In those cases the silicone often needs replacing or the bathroom re-grouping. Large patches found behind walls are a different matter: it recommends professional help if there is any chance of the toxic species it names.
Once the mould is dealt with and the cause has been addressed, the finish itself may need attention. Stained or flaking paint in a wet room will not hold if the substrate is still damp, so wait until the area is fully dry. A painter who specialises in painting kitchens and bathrooms can explain the preparation needed for your particular surface. Painting kitchens and bathrooms in a unit also needs to respect the rules: if the ceiling or wall is common property, the repaint is the body corporate's decision, not yours.
If the paint job is only for your side of a shared wall, mention it to neighbours who might be affected by noise or fumes, and keep ventilation running while it cures.
Under Tenancy Services guidance, rental homes must be free of mould and dampness before they are rented out, and tenants must keep the house aired and remove mould as soon as it appears. Tenants are expected to use extractor fans and open windows, dry washing outdoors where they can, keep wardrobes slightly open and pull furniture away from walls. If you are doing all of that and the mould persists, raise it in writing with the landlord, who can in turn ask the body corporate to investigate common property causes. For an owner-occupier the same sequence applies, with the committee standing in for the landlord.
When you collect quotes, ask each contractor, Eggshell & Co among them, how they deal with existing mould and moisture before a single coat goes on; comparing those answers side by side will help you judge the quotes.