Wipe the inside of an apartment window on a cold morning and the cloth comes away wet. Nothing is leaking. The water came from the air in the room, and in a modern, well-sealed unit it has fewer places to go than it would in an old draughty villa. Condensation is the first stage of the mould problem, and it is much easier to deal with at this stage than after the paint has started to stain.
Consumer NZ's explanation is straightforward. In winter the air cools, and cool air cannot hold as much water, so the moisture condenses on cold surfaces such as windows, sills, walls and ceilings. Mould is most likely where warm, moist air from showers and cooking meets those cold surfaces. The same guide puts numbers on the supply side: about 0.2 litres of moisture an hour from each person breathing, 1.5 litres a day per person from showers and baths, 3 litres a day from cooking and 5 litres from a load of washing dried indoors.
Add those up for two people in a one-bedroom unit and it is easy to see how much water ends up in the air each day if nothing carries it outside.
Several features of shared buildings make condensation more likely, and a couple of them are not in your control.
Consumer NZ groups its advice into removing water sources, ventilating and keeping the home warm, and the grouping is useful.
Moisture. Dry washing outside, in a garage or in a vented dryer if you can. Wipe condensation off glass and walls as it forms. Put lids on pots. Do not use portable unflued gas heaters indoors; both Consumer NZ and Tenancy Services warn they add moisture and fill the air with unwanted gases.
Air. Use the extractor fan while cooking or showering and leave it running for roughly ten minutes after. Open windows for ten to fifteen minutes in the morning. Keep furniture a little away from walls and leave wardrobe doors slightly ajar so air can move. If the unit has a mechanical ventilation system such as an HRV or DVS, make sure it is switched on and maintained.
Heat. Warmer air holds more moisture, so condensation forms less readily. Consumer NZ suggests opening curtains during the day for warmth and closing them just before dark, and sealing draughts around windows and doors.
The healthy homes standards put minimums on landlords. Under the heating standard, as set out by Tenancy Services, a rental needs at least one fixed heater that can directly heat the main living room, each heater must be at least 1.5 kW and meet the capacity the room needs, and open fires and unflued gas heaters do not qualify. For small apartments whose required capacity is modest, a smaller fixed electric heater with a thermostat may be acceptable.
The ventilation standard requires openable windows in living rooms, dining rooms, kitchens and bedrooms, with openable area of at least 5 percent of the room's floor area, plus extractor fans in kitchens and bathrooms that vent outside.
Apartments add a wrinkle. Tenancy Services' exemptions page says a landlord who does not own the whole building, an apartment for example, may be partially exempt because of restricted access or shared ownership, but must still take all reasonable steps to comply as far as practicable. The unit titles guidance gives an example where the body corporate's rules prohibit external heating units on shared property without consent; the landlord has to seek that consent and, failing it, install the best qualifying alternative that does not need an external unit.
Tenancy Services notes that damp and mould problems are most likely in autumn and winter, and that a well-aired home is easier to heat and healthier to live in. Wipe it away early. If dark spotting has already appeared, clean it promptly following the safe-handling advice from Consumer NZ: ventilate, wear gloves, eye protection and a P2 or N95 mask, and do not dry-brush.
Do not paint over it. A coating applied to a surface that is still damp or mouldy is unlikely to last, so the order that holds up is to fix the cause, clean the surface, let it dry and only then repaint. If you are working with a painter, ask how they deal with this before the first coat. A contractor page on treating mould before painting is one way to see how a company frames that step before you compare quotes.
A single damp corner in one room is likely to be something you can manage. Persistent condensation on an exterior wall, wet patches that do not respond to heat and airing, or stains that appear after rain suggest something else: a failed seal, a leak or a thermal bridge in the building envelope. Those are common property questions. Photograph the problem, record the dates and send it to the body corporate manager or committee chair in writing. If the cause is inside your unit's boundary, you will be responsible for repairs; if it is in the common property, the body corporate must maintain it, as the unit titles maintenance guidance sets out. When a repaint follows the repair, a firm such as Eggshell & Co can be asked to confirm in the quote that the surface will be checked and dried first.